f98 specifications type numbering system (example : 6.3v 10f) drawing l w 1 s 2 w 2 h s 1 m 1.6 0.1 0.85 0.1 0.65 0.1 0.8 0.1 0.5 0.1 0.6 0.1 u 1.10 0.05 0.60 0.05 0.35 0.05 0.55 0.05 0.3 0.05 0.5 0.05 ( mm ) cace code l h w 1 w 2 s 1 s 2 s 1 s 2.0 0.1 1.25 0.1 0.9 0.1 0.8 0.1 0.5 0.1 1.0 0.1 rated voltage (voltage code) j u case m case rated voltage (voltage code) capacitance code js s case taping code (refer to page 321 for details) f 1 9 2 8 3 0 4 j 5 1 6 0 7 6 8 m 9 m 10 11 case code capacitance tolerance rated capacitance rated voltage series marking standard ratings category temperature range capacitance tolerance leakage current dissipation factor damp heat (steady state) temperature cycles resistance to soldering heat surge ? endurance ? shear test performance characteristics 20 % (at 120hz) refer to the list below at 40 c , 90 to 95 % r.h., for 500hours (no voltage applied) capacitance change refer to the list below (* 1) dissipation factor 150 % or less of initial specified value leakage current 200 % or less of initial specified value refer to next page provided that after 5 minute's application of rated voltage, leakage current at 85 c , 10 times or less than 20 c specified value. after 5 minute's application of rated voltage, leakage current at 125 c , 12.5 times or less than 20 c specified value. at --55 c / +125 c , for 30 minutes each, 5 cycles capacitance change refer to the list below (* 1) dissipation factor 150 % or less than the initial specified value leakage current initial specified value or less at 260 c , for 10 seconds, reflow, capacitance change refer to the list below (* 1) leakage current initial specified value or less leakage current initial specified value or less after application of surge in series with a 1k ? resistor at the rate of 30 seconds on, 30 seconds off, for 1000 successive test cycles at 85 c , capacitors meet the characteristics requirements listed below. capacitance change refer to the list below (* 1) dissipation factor 150 % or less than the initial specified value leakage current 200 % or less than the initial specified value after 1000 hours' application of rated voltage in series with a 3 ? resistor at 85 c, capacitors meet the characteristic requirements listed below capacitance change refer to the list below (* 1) dissipation factor 150% or less than the initial specified value leakage current 200% or less than the initial specified value after applying the pressure load of 5n for 10 1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. then, there shall be found no remarkable abnormality on the capacitor terminals. item --55 to +125 c (rated temperature : 85 c) esr refer to the list below terminal strength 5n (0.51kg f) for 10 1 seconds 20 r230 45 45 1 mm resin-molded chip, high capacitance series ? as for the surge and derated voltage at 125 ? c , refer to page 320 for details. solid tantalum electrolytic capacitors ( ) the series in parentheses are being developed. please contact to your local nichicon sales office when these series are being designed in your application. compliant to the rohs directive (2002/95/ec). m 1 2.2 4.7 10 22 33 47 68 100 105 225 475 106 226 336 476 686 107 u u m m m (m) s (m) s u m u m m m m s (s) u m (u) m m (m) s s m m m s 4 6.3 10 16 20 25 0g 0j 1a 1c 1d 1e v cap.(f) code m --- --- --- a j n s w a 20 20 7.5 4 8 4 4 20 7.5 30 6 6 8 10 6 15 7.5 6 7.5 4 6 10 10 12 4 10 10 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 20 30 30 30 30 20 30 30 20 25 15 30 40 30 35 20 20 30 8 20 35 45 25 15 6 6 20 20 30 6 6 12 18 6 8 4.7 10 22 33 47 68 100 4.7 4.7 10 10 22 33 47 47 2.2 2.2 4.7 10 22 33 1 2.2 4.7 10 1 1 0.5 0.8 0.9 1.3 1.9 2.7 4.0 0.6 0.5 3.2 0.6 1.4 4.2 23.7 3.0 0.5 0.5 0.5 1.0 2.2 3.3 0.5 0.5 0.8 1.6 0.5 0.5 4v 6.3v 10v 16v 20v 25v f980g475mua f980g106mua f980g226mma f980g336mma f980g476mma f980g686msa F980G107MSA f980j475mua f980j475mma f980j106mua f980j106mma f980j226mma f980j336mma f980j476mma f980j476msa f981a225mua f981a225mma f981a475mma f981a106mma f981a226msa f981a336msa f981c105mma f981c225mma f981c475mma f981c106msa f981d105mma f981e105mma u u m m m s s u m u m m m m s u m m m s s m m m s m m ? c/c (%) part number leakage current ( a) *1 disspation factor (% @120hz) case code esr ( ? @100khz) rated volt rated capacitance (f) capacitance code * 1 : leakage current after 5 minute's application of rated voltage, leakage current at 20 ? c. cat.8100z
|
